Error Code | Description |
010 | “Framing error reported from HI-PRO” |
011 | “Receiver overrun error reported from HI-PRO” |
012 | “Receiver noise on line error reported from HI-PRO” |
015 | “Receiver timeout error reported from HI-PRO” |
020 | “Invalid message number reported from HI-PRO” |
021 | “Invalid message header reported from HI-PRO” |
022 | “Invalid data reported from HI-PRO” |
023 | “Message termination error reported from HI-PRO” |
030 | “Too many characters in argument reported from HI-PRO” |
031 | “Too few data in stream argument reported from HI-PRO” |
032 | “Too many data in stream argument reported from HI-PRO” |
033 | “Data argument out of valid range reported from HI-PRO” |
034 | “Too few data in hex byte data block reported from HI-PRO” |
035 | “Requested data is not available reported from HI-PRO” |
036 | “Invalid data in input buffer reported from HI-PRO” |
037 | “Invalid communication mode reported from HI-PRO” |
038 | “Timing too fast reported from HI-PRO” |
040 | “Out of memory reported from HI-PRO” |
041 | “Learn is not started reported from HI-PRO” |
042 | “All ready in learn mode reported from HI-PRO” |
043 | “No output bit stream defined reported from HI-PRO” |
044 | “No input specification defined reported from HI-PRO” |
045 | “No pin specification defined reported from HI-PRO” |
046 | “H.I. timeout reported from HI-PRO” |
047 | “The connected HI-PRO could not be authenticated (Device authentication). Please contact your supplier for assistance” |
048 | “Input Buffer is Full reported from HI-PRO” |
049 | “ADC timeout reported from HI-PRO” |
050 | “Checksum error reported from HI-PRO” |
051 | “Flash verify error reported from HI-PRO” |
052 | “Invalid downloaded program reported from HI-PRO” |
099 | “Undefined error reported from HI-PRO” |
200 | “TIMEOUT”“HI-PRO does not respond”“Check power and RS232 connections” |
201 | “Error in WriteComm?”“GetCommError? returns %d” |
202 | “Error in OpenComm?”“COM port may be in use by another device. Try to change COMPort= in HIPRO.INI.” |
203 | “Error in SetCommState?” |
204 | “Error in BuildCommDCB” |
205 | “User was not logged in” |
206 | “HI-PRO has been reset ( settings lost )” |
207 | “Invalid data received from HI-PRO” |
208 | “Invalid header received from HI-PRO” |
209 | “Too big stream received from HI-PRO” |
210 | “Numerics received from HI-PRO is out of range” |
211 | “No terminator in data from HI-PRO” |
212 | “Incomplete block received from HI-PRO” |
213 | “Error in ReadComm?”“GetCommError? returns %d” |
214 | “Unexpected data from HI-PRO” |
215 | “Bad CheckSum? in data received from HI-PRO” |
216 | “Error in CloseComm?” |
217 | “Bad Parameter send to instrument driver” |
218 | “VBat low. Disconnect HI from HI-PRO” |
219 | “Self test status error” |
221 | “Receiver overflow”“Input buffer too small or not emptied” |
222 | “Overrun”“Interrupts disabled too long time. Try lower baudrate.” |
223 | “Parity error” |
224 | “Framing error”“Wrong instrument connected or instrument turned off” |
225 | “Break detected”“Wrong instrument connected or instrument turned off” |
226 | “Transmission queue was full”“Output buffer too small” |
227 | “Requested mode is not supported, or the idComDev parameter is invalid” |
228 | “Transmission queue never empties! Maybe IRQ conflict” |
229 | “The connected HI-PRO could not be authenticated (PC Driver authentication). Please contact your supplier for assistance” |
255 | “Unknown error” |