| Error Code | Description |
|---|---|
| 010 | “Framing error reported from HI-PRO” |
| 011 | “Receiver overrun error reported from HI-PRO” |
| 012 | “Receiver noise on line error reported from HI-PRO” |
| 015 | “Receiver timeout error reported from HI-PRO” |
| 020 | “Invalid message number reported from HI-PRO” |
| 021 | “Invalid message header reported from HI-PRO” |
| 022 | “Invalid data reported from HI-PRO” |
| 023 | “Message termination error reported from HI-PRO” |
| 030 | “Too many characters in argument reported from HI-PRO” |
| 031 | “Too few data in stream argument reported from HI-PRO” |
| 032 | “Too many data in stream argument reported from HI-PRO” |
| 033 | “Data argument out of valid range reported from HI-PRO” |
| 034 | “Too few data in hex byte data block reported from HI-PRO” |
| 035 | “Requested data is not available reported from HI-PRO” |
| 036 | “Invalid data in input buffer reported from HI-PRO” |
| 037 | “Invalid communication mode reported from HI-PRO” |
| 038 | “Timing too fast reported from HI-PRO” |
| 040 | “Out of memory reported from HI-PRO” |
| 041 | “Learn is not started reported from HI-PRO” |
| 042 | “All ready in learn mode reported from HI-PRO” |
| 043 | “No output bit stream defined reported from HI-PRO” |
| 044 | “No input specification defined reported from HI-PRO” |
| 045 | “No pin specification defined reported from HI-PRO” |
| 046 | “H.I. timeout reported from HI-PRO” |
| 047 | “The connected HI-PRO could not be authenticated (Device authentication). Please contact your supplier for assistance” |
| 048 | “Input Buffer is Full reported from HI-PRO” |
| 049 | “ADC timeout reported from HI-PRO” |
| 050 | “Checksum error reported from HI-PRO” |
| 051 | “Flash verify error reported from HI-PRO” |
| 052 | “Invalid downloaded program reported from HI-PRO” |
| 099 | “Undefined error reported from HI-PRO” |
| 200 | “TIMEOUT”“HI-PRO does not respond”“Check power and RS232 connections” |
| 201 | “Error in WriteComm?”“GetCommError? returns %d” |
| 202 | “Error in OpenComm?”“COM port may be in use by another device. Try to change COMPort= in HIPRO.INI.” |
| 203 | “Error in SetCommState?” |
| 204 | “Error in BuildCommDCB” |
| 205 | “User was not logged in” |
| 206 | “HI-PRO has been reset ( settings lost )” |
| 207 | “Invalid data received from HI-PRO” |
| 208 | “Invalid header received from HI-PRO” |
| 209 | “Too big stream received from HI-PRO” |
| 210 | “Numerics received from HI-PRO is out of range” |
| 211 | “No terminator in data from HI-PRO” |
| 212 | “Incomplete block received from HI-PRO” |
| 213 | “Error in ReadComm?”“GetCommError? returns %d” |
| 214 | “Unexpected data from HI-PRO” |
| 215 | “Bad CheckSum? in data received from HI-PRO” |
| 216 | “Error in CloseComm?” |
| 217 | “Bad Parameter send to instrument driver” |
| 218 | “VBat low. Disconnect HI from HI-PRO” |
| 219 | “Self test status error” |
| 221 | “Receiver overflow”“Input buffer too small or not emptied” |
| 222 | “Overrun”“Interrupts disabled too long time. Try lower baudrate.” |
| 223 | “Parity error” |
| 224 | “Framing error”“Wrong instrument connected or instrument turned off” |
| 225 | “Break detected”“Wrong instrument connected or instrument turned off” |
| 226 | “Transmission queue was full”“Output buffer too small” |
| 227 | “Requested mode is not supported, or the idComDev parameter is invalid” |
| 228 | “Transmission queue never empties! Maybe IRQ conflict” |
| 229 | “The connected HI-PRO could not be authenticated (PC Driver authentication). Please contact your supplier for assistance” |
| 255 | “Unknown error” |