ezfit:5x:conformance

Slow System: Pentium IV, 3.0 GHz, 2 GB RAM, 100 GB free hard disk space.
Up-to-date System. Minimum Requirements: Intel QuadCore, 3.0 GHz, 2 GB RAM, 100 GB free hard disk space.
Programming Box:
- HI-PRO Classic, HI-PRO USB, HI-PRO 2.
- EMiniTec & EMiniTec 2 Programmer (USB).
- NOAHlink.

Slow System: Windows XP SP3, .NET 4.0.3 Framework, NOAH 4.1 or greater.
Up-to-date System: Windows 7/8/10, .NET 4.6 Framework, NOAH 4.7, ezFIT.

<table width="100%" border="1" cellspacing="0" cellpadding="1" class="inline"> <tr> <th width="5%">Step</th> <th width="42%">Description</th> <th width="42%">Expected Behavior</th> <th width="11%">Test Result</th> </tr> <tr valign="top"> <td>1</td> <td><p>Run ezFIT installation.</p> <p>Follow installation instructions.</p></td> <td><p>The application install successfully.</p> <p>Depending on the implementation, a screen with a <Finish> button appears, or the option to reboot the computer for changes to take place.</p> <p>If the application installation requires the computer to be rebooted, please exit, reboot and start the application.</p></td> <td> </td> </tr> <tr valign="top"> <td>2</td> <td>Verify that no system components were downgraded during installation. This should include FireBird, database files, programmer driver files, and Noah library.</td> <td>No system components were downgraded.</td> <td> </td> </tr> <tr valign="top"> <td>3</td> <td>Enter a new Patient (Last Name, First Name, Birth Date) and save it.</td> <td>Application saves patient record.</td> <td> </td> </tr> <tr valign="top"> <td>4</td> <td>Enter an Audiogram for the patient and save it.</td> <td>Application saves patient audiogram.</td> <td> </td> </tr> <tr valign="top"> <td>5</td> <td>Select Tools > General, and configure the correct Programming Box setting (usually "Hi-Pro (Classic or USB)").</td> <td> </td> <td> </td> </tr> <tr valign="top"> <td>6</td> <td>Perform a simulated fitting by clicking on Instruments button, selecting a product, then clicking on the Simulate button.</td> <td>Fitting screen in Simulation mode appears.</td> <td> </td> </tr> <tr valign="top"> <td>7</td> <td>Perform an Initial Fit for that instrument. Click on Initial Fit button, select the appropriate memories and desired environment settings, then press <Fit Selected > button.</td> <td>Graph curves and other settings get adjusted automatically.</td> <td> </td> </tr> <tr valign="top"> <td>8</td> <td>Save the changes (press <Save & Program&gt).</td> <td>A new fitting session appears under the Patient Information > Session List.</td> <td> </td> </tr> </table>

<table width="100%" border="1" cellpadding="1" cellspacing="0" class="inline"> <tr> <th width="5%">Step</th> <th width="42%">Description</th> <th width="42%">Expected Behavior</th> <th width="11%">Test Result</th> </tr> <tr valign="top"> <td>1</td> <td><p>Run ezFIT.</p></td> <td><p>The application opens successfully.</p></td> <td> </td> </tr> <tr valign="top"> <td>2</td> <td>Select an existing patient record or enter a new one (Last Name, First Name, Birth Date) and save it.</td> <td>A patient record is ready for fitting.</td> <td> </td> </tr> <tr valign="top"> <td>3</td> <td>Perform a simulated fitting by clicking on the Instruments button, selecting a product, then selecting the Simulate button.</td> <td>Simulation screen appears.</td> <td> </td> </tr> <tr valign="top"> <td>4</td> <td>Exit application by clicking on X (top right window corner).</td> <td>Exits application with no errors or memory leaks.</td> <td> </td> </tr> <tr valign="top"> <td>5</td> <td>Perform Steps 1 - 3. Then, exit application by pressing <Alt><F4>.</td> <td>Exits application with no errors or memory leaks.</td> <td> </td> </tr> </table>

<table width="100%" border="1" cellpadding="1" cellspacing="0" class="inline"> <tr> <th width="5%">Step</th> <th width="42%">Description</th> <th width="42%">Expected Behavior</th> <th width="11%">Test Result</th> </tr> <tr valign="top"> <td>1</td> <td><p>Run ezFIT.</p></td> <td><p>The application opens successfully.</p></td> <td> </td> </tr> <tr valign="top"> <td>2</td> <td>Enter a new Patient (Last Name, First Name, Birth Date) and save it.</td> <td>Application saves patient record.</td> <td> </td> </tr> <tr valign="top"> <td>3</td> <td>Enter an Audiogram for the patient and save it.</td> <td>Application saves patient audiogram.</td> <td> </td> </tr> <tr valign="top"> <td>4</td> <td>Select Tools and configure the correct Programming Box setting (usually "Hi-Pro (Classic or USB)").</td> <td> </td> <td> </td> </tr> <tr valign="top"> <td>5</td> <td>Perform a simulated fitting by clicking on Instruments, selecting a product, then selecting Simulate.</td> <td>Fitting screen in Simulation mode appears.</td> <td> </td> </tr> <tr valign="top"> <td>6</td> <td>Perform an Initial Fit for that instrument. Click on Initial Fit, select the appropriate memories and desired environment settings, then press <Fit Selected> button.</td> <td>Graph curves and other settings get adjusted automatically, and checkboxes get cleared.</td> <td> </td> </tr> <tr valign="top"> <td>7</td> <td>Modify some of the settings to try and stress the system. This could be in Solutions (Basic or Advanced), individual parameters, menus, etc.</td> <td>No errors.</td> <td> </td> </tr> <tr valign="top"> <td>8</td> <td>Save the changes (press <Save & Program>).</td> <td>A new fitting session appears under the Patient Information > Session List.</td> <td> </td> </tr> </table>

For Full Conformance Test
Perform Steps 5 - 8 with each supported product (hearing instrument), reading an instrument each time (not in simulation mode)	Supported Product List
For Limited Conformance Test
Perform Steps 5 - 8 with one product (hearing instrument) from each supported circuit, reading an instrument each time (not in simulation mode)	Supported Product List

<table width="100%" border="1" cellpadding="1" cellspacing="0" class="inline"> <tr> <th width="5%">Step</th> <th width="42%">Description</th> <th width="42%">Expected Behavior</th> <th width="11%">Test Result</th> </tr> <tr valign="top"> <td>1</td> <td><p>Run ezFIT.</p></td> <td><p>The application opens successfully.</p></td> <td> </td> </tr> <tr valign="top"> <td>2</td> <td>Select a patient record.</td> <td>Screen shows patient data.</td> <td> </td> </tr> <tr valign="top"> <td>3</td> <td>Select from top toolbar: Reports > Print</td> <td>Fitting report print preview appears, and gets printed.</td> <td> </td> </tr> </table>

<table width="100%" border="1" cellpadding="1" cellspacing="0" class="inline"> <tr> <th width="5%">Step</th> <th width="42%">Description</th> <th width="42%">Expected Behavior</th> <th width="11%">Test Result</th> </tr> <tr valign="top"> <td>1</td> <td><p>Run ezFIT.</p></td> <td><p>The application opens successfully.</p></td> <td> </td> </tr> <tr valign="top"> <td>2</td> <td>Select Tools.</td> <td>'Settings' window shows up.</td> <td> </td> </tr> <tr valign="top"> <td>3</td> <td>Select Database tab, press <Test Connection></td> <td>Network connection succeeds.</td> <td> </td> </tr> </table>

<table width="100%" border="1" cellpadding="1" cellspacing="0" class="inline"> <tr> <th width="5%">Step</th> <th width="42%">Description</th> <th width="42%">Expected Behavior</th> <th width="11%">Test Result</th> </tr> <tr valign="top"> <td> </td> <td><p>Run ezFIT.</p></td> <td><p>The application opens successfully.</p></td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Configure application to use Hi-Pro (Tools > Programming Box) </td> <td> </td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Update the HIPRO.INI file (<tt>C:\Program Files (x86)\Audina\ezFIT5\</tt> or <tt>C:\WINDOWS\</tt> ) by running the HIPRO Test program (Tools > Hi-Pro Test).</td> <td>File contents should be something like this:<br> <table width="75%" border="1" cellspacing="0" cellpadding="1"> <tr> <th>HIPRO.INI file</th> </tr> <tr> <td bgcolor="#FFFFFF">[Settings]<br> COMPort=COM2<br> Baudrate=19200<br> SwPort=NONE<br> AuricalSwitch=NONE<br> LanguageWIN=HIPROWIN.uk<br> LanguageDOS=HIPRODOS.uk</td> </tr> </table> <br> </td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Run Intricon's Slider to check that the Hi-Pro COM port is not in use.</td> <td>No error messages.</td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Save the HIPRO.INI file in the file HIPROx.INI</td> <td> </td> <td> </td> </tr> <tr valign="top"> <td> </td> <td><p>Select a hearing instrument and perform fitting.</p> <p><strong>Note:</strong> During data transfer, unplug the power to the Hi-Pro and check that it is possible to re-establish communication without getting the module to hang or crash.</p></td> <td><p>The selected hearing instrument has been programmed.</p> <p>The application should not hang or crash during a shutdown of the Hi-Pro.</p></td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Save the fitting (press <Program>) and exit the application.</td> <td>The fitting session is saved and the application is closed.</td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Compare the HIPROx.INI and HIPRO.INI files with the program FCOMPARE.EXE (or DIFF.EXE)</td> <td>No differences are detected.</td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Run Intricon's Slider to check that the Hi-Pro COM port is not in use.</td> <td>No error messages.</td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Read a hearing instrument using Slider.</td> <td>Slider reads the instrument with no problems.</td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Close Slider.</td> <td>Slider closes with no errors.</td> <td> </td> </tr> </table>

<table width="100%" border="1" cellpadding="1" cellspacing="0" class="inline"> <tr valign="top"> <td colspan="2">Pre-condition: This test should only be performed with products that support the EMiniTec (Intricon). The EMiniTec should use the latest drivers available. </td> <td colspan="2"><p>Post-condition: A new test patient that includes the following data should be created:</p> <ul> <li>An audiogram.</li> <li>3 fitting sessions that support the EMiniTec.</li> </ul></td> </tr> <tr> <th width="5%">Step</th> <th width="42%">Description</th> <th width="42%">Expected Behavior</th> <th width="11%">Test Result</th> </tr> <tr valign="top"> <td> </td> <td><p>Run ezFIT.</p></td> <td><p>The application opens successfully.</p></td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Configure application to use EMiniTec (Tools > Programming Box) </td> <td> </td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Click on the Audiological Information button.</td> <td>The audiogram screen displays.</td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Create an audiogram with the following dB values for frequencies 250, 500, 750, 1k, 1.5k, 2k and 4k Hz:<br> HTL, Right = 40 dB<br> HTL, Left = 45 dB</td> <td>The audiogram curves are drawn according to the specified data.</td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Save the audiogram.</td> <td> </td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Select a hearing instrument and perform fitting on both ears (using the EMiniTec). </td> <td>The selected hearing instrument has been programmed.</td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Save the fitting (press <Save & Program>) and exit the application.</td> <td>A new fitting session is created and the application is closed.</td> <td> </td> </tr> </table>

<table width="100%" border="1" cellpadding="1" cellspacing="0" class="inline"> <tr valign="top"> <td colspan="2">Pre-condition: This test should only be performed with products that support the NOAHlink (Intricon products, except Intuition BTEs; OnSemi products except BTEs). The NOAHlink should use the latest drivers available. </td> <td colspan="2"><p>Post-condition: A new test patient that includes the following data should be created:</p> <ul> <li>An audiogram.</li> <li>3 fitting sessions that support the NOAHlink.</li> </ul></td> </tr> <tr> <th width="5%">Step</th> <th width="42%">Description</th> <th width="42%">Expected Behavior</th> <th width="11%">Test Result</th> </tr> <tr valign="top"> <td> </td> <td><p>Run ezFIT.</p></td> <td><p>The application opens successfully.</p></td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Configure application to use NOAHlink (Tools > Programming Box) </td> <td> </td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Click on the Audiogram tab.</td> <td>The audiogram screen displays.</td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Create an audiogram with the following dB values for frequencies 250, 500, 750, 1k, 1.5k, 2k and 4k Hz:<br> HTL, Right = 40 dB<br> HTL, Left = 45 dB</td> <td>The audiogram curves are drawn according to the specified data.</td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Save the audiogram.</td> <td> </td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Select a hearing instrument and perform fitting on both ears (using the NOAHlink). </td> <td>The selected hearing instrument has been programmed.</td> <td> </td> </tr> <tr valign="top"> <td> </td> <td>Save the fitting (press <Save & Program>) and exit the application.</td> <td>A new fitting session is created and the application is closed.</td> <td> </td> </tr> </table>

<table width="100%" border="1" cellpadding="1" cellspacing="0" class="inline"> <tr> <th width="5%">Step</th> <th width="42%">Description</th> <th width="42%">Expected Behavior</th> <th width="11%">Test Result</th> </tr> <tr valign="top"> <td>1</td> <td><p>Run ezFIT.</p></td> <td><p>The application opens successfully.</p></td> <td> </td> </tr> <tr valign="top"> <td>2</td> <td>Run ezBackup. Select from the main menu: Tools > Tools > Backup.</td> <td>The application ezBackup utility opens successfully.</td> <td> </td> </tr> <tr valign="top"> <td>3</td> <td>Backup database. Select Export tab, then press < Export > button. If file already exists, say "Yes" to question "Overwrite this file?"</td> <td>Backup is completed sucessfully.</td> <td> </td> </tr> <tr valign="top"> <td>4</td> <td>Exit ezBackup utility.</td> <td>The application ezBackup closes with no error messages.</td> <td> </td> </tr> <tr valign="top"> <td>5</td> <td>Run ezBackup. Select from the main menu: Tools > Tools > Backup.</td> <td>The application ezBackup utility opens sucessfully.</td> <td> </td> </tr> <tr valign="top"> <td>6</td> <td>Restore database. Select Import tab, then press < Import > button.</td> <td>Restore is completed successfully.</td> <td> </td> </tr> <tr valign="top"> <td>7</td> <td>Exit ezBackup utility.</td> <td>The application ezBackup closes with no error messages.</td> <td> </td> </tr> </table>

<table width="100%" border="1" cellpadding="1" cellspacing="0" class="inline"> <tr> <th width="5%">Step</th> <th width="42%">Description</th> <th width="42%">Expected Behavior</th> <th width="11%">Test Result</th> </tr> <tr valign="top"> <td>1</td> <td><p>Run ezFIT.</p></td> <td><p>The application opens successfully.</p></td> <td> </td> </tr> <tr valign="top"> <td>2</td> <td><p>Try to simulate the use of the application in a dispenser workshop.<br> Create several patient records (with their respective audiograms).<br> Perform fittings for all of these patients using different hearing instruments.</p> <p>Print Fitting report.</p></td> <td>The application should perform as intended and the reports printed correctly.</td> <td> </td> </tr> <tr valign="top"> <td>3</td> <td>Try to stress and crash the application by clicking on different buttons and menu items within application. This should be performed under Windows 7/8. This ad-hoc testing should be performed for a time period of at least 15 minutes.</td> <td>The module should not crash or lock the system.</td> <td> </td> </tr> <tr valign="top"> <td>4</td> <td>Exit application.</td> <td>Application is closed down.</td> <td> </td> </tr> </table>

<table width="100%" border="1" cellpadding="1" cellspacing="0" class="inline"> <tr valign="top"> <th colspan="2">The application has successfully passed the above test sequences. The supporting log files and/or manual test worksheets have been included.</th> </tr> <tr valign="top"> <td width="70%">Signature<br />(It is acceptable to type in the name and date if the report is being sent electronically)</td> <td width="30%"> </td> </tr> <tr valign="top"> <td>Date</td> <td> </td> </tr> </table>

ezFIT 5.x Conformance Tests

Issues Tested

Time Estimate for Product Tests

Test Environment

Hardware

Software

Conformance Test Report

Test Sequences

Test Sequence 1: Application Installation

Test Sequence 2: Application Launch and Shutdown

Test Sequence 3: Handling Hearing Instruments and Fittings

Test Sequence 4: Application Printing

Test Sequence 5: System Options

Test Sequence 6: Communication with the HI-PRO Programmer

Test Sequence 7: Communication with the EMiniTec Programmer

Test Sequence 8: Communication with the NOAHlink Programmer

Test Sequence 9: Backup and Restore Data using ezBackup

Test Sequence 10: Un-structured Test

Sign-off